Laser cutting machine, laser marking machine, laser engraving machine large professional equipment manufacturer

laser cutter

laser marking machine

Laser engraving machine

Large professional equipment manufacturer

Equipment maintenance

  • Specifications for the repair and maintenance of mechanical transmission components in laser equipment -2008-03-24
  • Description of content: How to make the laser equipment work normally and stably and make better use of its ergonomics, the most important thing is the daily maintenance and maintenance of the equipment. Well done, not only can extend the service life of the machine, reduce the equipment failure rate, but also improve the product quality, and ultimately achieve stable and efficient production. In order to make better use of this equipment, the following is a brief introduction to the daily maintenance, maintenance and replacement of the mechanical transmission parts of laser equipment: ...
  • Yueming laser engraving machine safety precautions -2008-01-22
  • brief introduction:

    1. During the work of the machine, it is forbidden for the operator to leave without authorization to avoid unnecessary losses.
    2. When the machine is working, the top cover of the machine must be covered to prevent the laser from deviating and hurting people.
    3. Because there are laser and high voltage parts in the machine, non-professionals are strictly prohibited to disassemble the machine without authorization.
    ...

  • Marking machine series precautions and maintenance -2008-03-24
  • Introduction: First, matters needing attention

    a. The working environment (room temperature) is required to be 18 ْ C -28 ْ C (25 ْ C is the best)
    b. It is strictly forbidden to start the laser power supply and Q driver in the absence of water or abnormal circulation.
    c. When abnormal phenomenon occurs, first turn off the laser power and galvanometer power, and then check
    e. It is not allowed to start other components before the cymbal lamp is ignited to prevent high voltage from penetrating and damaging the components
    f. Laser power output ...
  • Daily maintenance and precautions -2008-03-24
  • Introduction: The stable and normal operation of the machine is inseparable from the normal operation and daily maintenance. The following will introduce the laser cutting machine

    Routine maintenance:

    1. Water replacement and cleaning of the water tank (It is recommended to clean the water tank and replace the circulating water once a week)
    Note: Make sure that the laser tube is filled with circulating water before the machine works.
    The quality and temperature of the circulating water directly affect the use of the laser tube ...
  • Precautions for using glass CO2 laser tube -2008-03-24
  • Content introduction: 1. Please turn on the cooling water first when using, adjust the position of the water outlet pipe by using the principle of low inlet and high outlet, and ensure that the cooling water is filled with the cooling pipe. There must be no bubbles in the tube, and then turn on the power. Requirement: The cooling water is soft water (distilled or purified water), and the temperature of the cooling water should be paid attention to. The temperature of the water should be controlled in the range of 25 ℃ -30 ℃, not too high or too low, especially in summer, if the water temperature is too high, The cooling water should be replaced in time or when the machine is stopped for a while ...
    
<% Set objConn = Server.CreateObject ("ADODB.Connection") objConn.ConnectionString = "Provider = Microsoft.Jet.OLEDB.4.0;" & _ "Data Source =" & Server.MapPath ("../../ SiteFiles /Data.asax ") objConn.Open strSQL =" SELECT id, Title FROM au_Content where NodeID = 804 "Set objRS = Server.CreateObject (" ADODB.Recordset ") objRS.Open strSQL, objConn, 1, 1 Count = objRS. RecordCount Item = 10 redim a (Item, 2), t (Count) for each j in tj = 0 next Randomize timer for j = 1 to Item k = int (rnd * Count + 1) do while t (k) <> 0 k = int (rnd * Item + 1) loop t (k) = 1 next j = 1: i = 1 Do While Not objRS.Eof if t (j) = 1 then a (i, 1) = objRS (" id ") a (i, 2) = objRS (" Title ") i = i + 1 end if j = j + 1 objRS.MoveNext Loop for i = 1 to Item Response.write" "& a (i, 2) & " " next objRs.Close set objRs = nothing objConn.Close set objConn = nothing%>
  • Copyright © 2001-2009 abalonedoc.com All Right Reserved. Guangdong Han's Yueming Laser Technology Co., Ltd. All rights reserved
  • Market headquarters sales hotline: 0769-89838888, 89839999 laser cutting machine , laser marking machine , laser engraving machine Large professional laser equipment manufacturer
真人游戏平台注册 手机电玩平台 欢乐拼三张 必赢真人娱乐